Product ReviewsLee 90366 Double Cavity Mold

Perfect bullets First pour!

The key to a perfect bullet, on the first pour, is to Follow the directions! Clean,,Clean,,then clean the mold. Smoke it with a few WOODEN matches, then "I" use Graphite to lube the sprue plate, and heat the mold in the cast, (lower temps cast better bullets). As long as you follow directions for ALUMINUM MOLDS you should get a perfect, or near so, the First time! If you are new to "Boolit" casting, or an Old slug like me, the Lee Molds cannot be beat, for quality vs price, and I have Never seen one "Wear out" if given any care at all. My Only complaint, is their fairly "limited" bullet selections. (Just my opinion, there are many gaps in styles vs/sizes.)
If you want harder bullets you can "Water Drop" them. BUTNever get water in your casting pot, it Will ERUPT VIOLENTLY showering Molten Lead Everywhere! [I keep the water bucket BEHIND ME!]
Again, you can't beat the value of ANY Lee Reloading Products! I have All makes of equipment and the Lee Die's have become My favorite, because they are So easy to adjust, and if you do your part, and trim uniformly, they will make as consistant rounds, as dies costing 4 times as much! And the "Factory Crimp" die, that comes free in many sets, is a fantastic tool. Not to mention that most Lee die sets, have the correct shell holder, and a powder measure included free as well! I am not offilliated with Lee or anyone. I just like the cost to quality ratio, and if a tool Outlives ME, then what more could I ask?Read full review...

Verified purchase:  Yes | Condition: new | Sold by: shootingsupply

Lee Double Cavity Bullet Mold.

After cleaning the lee mold it cast very good bullets right from the start I cast up approximately 200 bullets. They released from the mold freely with no problems, very easy to cast with. Everything was OK till I weighted out the bullets, One cavity weighted more than the other, not a lot about 2 grs but more than I like. Not a big deal .Read full review...

Verified purchase:  Yes | Condition: new | Sold by: mspsports

Good mold. The new style blocks are a great improvement.

I am a hobbyist, and wanted a new mold to experiment with, for a 1-14 twist rifle barrel. Since Lee redesigned their mold blocks, the alignment of the 2 halves on the new molds, such as this, are very good, compared to the old ones. I used to shun Lee molds, but since the new design, I am sold.Read full review...

Cal .308 Flat Nose 150 gr Bullet Mold

The mold is much better than the old style Lee Molds. The alignment pins are better. The design will allow rounds to be loaded in a tube magazine and not damage the primer of the round on top.

Verified purchase:  Yes | Condition: new | Sold by: shootingsupply

Made of aluminum. Will not rust. Cast bullets from this mold actually fit my M 1 A. Only cast bullets from this particular mold will chamber in M1A

Produces lead bullets that actually chamber and fit in my 762X51 caliber M1A rifle.

Verified purchase:  Yes | Condition: new | Sold by: shootingsupply

superior dies!

casting just fall out of the mold they are a perfect .309dia and their ight weight.

Verified purchase:  Yes | Condition: new | Sold by: shootingsupply

great bullet mold

I bought this to test in my 300 Blk pistol AR. A quality Lee mold.

Verified purchase:  Yes | Condition: new | Sold by: shootingsupply

30/30 mold

Have molded over 200 bullets with this mold and it's a good product.

Verified purchase:  Yes | Condition: new | Sold by: mspsports

Very good product.

Very satisfied .

Verified purchase:  Yes | Condition: new | Sold by: reloaderschoice

mold

great mold use with gas check 1-2" moa at 100 yds

Verified purchase:  Yes | Condition: new | Sold by: shootingsupply