About
All feedback (45)
- carengine-37 (568)- Feedback left by buyer.Past monthVerified purchaseThank you for an easy, pleasant transaction. Excellent buyer. A++++++.
- joyearautoparts (207)- Feedback left by buyer.Past monthVerified purchaseHope to deal with you again. Thank you.
- acs-motorsport (10288)- Feedback left by buyer.Past 6 monthsVerified purchaseThank you for your support. Look forward to your next visit.
- *****- Feedback left by buyer.Past 6 monthsVerified purchaseQuick response and fast payment. Perfect! THANKS!!
- autospares6 (991)- Feedback left by buyer.Past 6 monthsVerified purchaseValued customer, Thanks for an easy, pleasant transaction. Excellent buyer.A++十+
- dropacctrading (1185)- Feedback left by buyer.Past 6 monthsVerified purchaseThank you for an easy, pleasant transaction. Excellent buyer. A++++++.
Reviews (3)
Feb 07, 2025
Title should be changed to the ilder arm bracket
Comparing this part to the my original part it had a major difference other wise the part was the same. This product had (2) zerk fittings, why? One was on the top and the second was on the side. Would have been nice it the vendor would have included another zerk fitting. The zerk fitting on the side matches the original part. I had to use the old zerk fitting for the top hole. The grease would have leaked out the other hole unless the hole was plugged or add another zerk fitting. This part should match exactly to the original.
Feb 03, 2025
One of the outer tie rod grease zerk fit...
One of the outer tie rod grease zerk fitting was too small. Had to use the my zerk fitting off the old part.
Oct 09, 2023
Product does not fit to the body as stated. Gaps on all four fenders. Fasteners provided did not work. Piece of crap. Don't buy these.
The feedback is requested from eBay regarding both you as a seller and representative of the products you sell. I had mentioned before about instructions of which there were none and the second most important item you never addressed was the push pin fasteners provided that did not work. You sent me a video in place of the instructions for someone else's product that actually conformed to the body with molding and fit perfectly without any gaps. I had to purchase nylon fasteners to secure these to the body, however, from the pictures provided the left and right front fenders had a half-inch gap in the front. Overall, all four fender flares have gaps in the corners. The top two holes line up on the fenders but the remaining holes on the flares do not align to the vehicle holes. Additionally, as mentioned in my first messages indicated that there was too much tension on the front and rear side of the fenders. You did not address my concerns with this as mentioned that they would break loose so that wouldn't look good. This job of installing these fender flares should have taken 1 hour. On the right rear fender flare alone, I spent 2-3 hours with a second person trying to make it work and fit properly but no matter how much pressure and force we used to get it aligned to the vehicle indents it wasn't going to work.
It's too late to send it back and receive a refund. I wasted my time and money. Please advise before I reach back to eBay and update my feedback regarding your product with additional pictures.
Message to the vendor when I first started installing the fenders:
Finally getting around to installing these fenders. No instruction in the box, only 4 fender flares and plastic fasteners. So in working on attaching the passenger right fender flare, I was able to attach the top 2 fasteners with the push pin. Apparently, the fasteners that came with the fender flare seem really cheap as I was only the top 2 fasteners. There is a lot of tension on the side mounting holes that the fasteners do not hold the fender. Even the push pin does not spread the fastener at the end to allow the fastener to hold the fender under tension from the new fender flare. I felt like if I hit a bump in the road the fender flare would detach from the vehicle. I didn't even get past the third fastener before deciding to take the fender off.
Bottom line: the fastener is able to go through the hole, however, the push pin barely spreads the end to secure the fender to the body.
Another message regarding the video of someone else's product:
I was able to get a video. Maybe it will help. However, another vendor's product actually fit properly with molding and no gaps.
Looking for a suggestion. Also, was there any additional mounting foam or rubber insulation for the flares or does the fender just mount right against the body?
His technician indicated no molding.
Recommendation: don't waste your time and money on these.
Have a great day.