About
All feedback (235)
- nostalgiaink (3269)- Feedback left by buyer.More than a year agoVerified purchaseGreat buyer!! Prompt payment!! Valued customer!! A+
- gruv-entertainment (417187)- Feedback left by buyer.Past 6 monthsVerified purchaseGood buyer, prompt payment, valued customer, highly recommended.
- 8space-travel8 (13131)- Feedback left by buyer.Past 6 monthsVerified purchaseGood buyer, prompt payment, highly recommended-Thank You:)
- larsonenterprises (15068)- Feedback left by buyer.Past 6 monthsVerified purchaseThank you for an easy, pleasant transaction. Excellent buyer. A++++++.
- bullseyeindustrialsales (56145)- Feedback left by buyer.More than a year agoVerified purchaseGood buyer, prompt payment, valued customer, Thanks from the Bullseye Team
- new-autosupply (8993)- Feedback left by buyer.More than a year agoVerified purchaseGood buyer, prompt payment, valued customer, highly recommended.
Reviews (9)
May 20, 2020
Good refrigerant
2 of 2 found this helpful Bought a project Mazda 6. One of the problems was a leak in the refrigerant and I was out of 134a so I bought this. Previous mechanic swapped in a new motor and recharged it right before I bought the vehicle and it only held the charge for a couple days. Drew a vacuum on system and found that it would leak down within 2 minutes. Changed out o-rings one at a time until it held vacuum for 30 minutes. Then it was charged from this bottle with the recommended 1.1 lbs and now it cools like a new car. No complaints.
Feb 16, 2022
Also Works for LB2204
Bought this to replace the one on my Kioti LB2204 and it is identical to the original, except without the several leaks that the old one had. This is an OEM Kioti part and had Kioti printed on the packaging. Installed it right away and have been using it for a little over a week. No leaks or other issues. Very happy with it.
Aug 06, 2016
Good Stir Plate
The stir plate works great for this price. It will kick the stir bar if you pour in too much powder, but I've never used a stir plate that didn't. I used to work in several chemistry and biological science laboratories, so I've used some rather expensive ones. If you're doing large cultures, like more than 1L, I'd recommend getting a bigger stir plate. Up to 1L it will pull a vortex all the way down to the included 1-inch bar with just water in there, so it's fine for smaller stuff. If you plan to let this run overnight, bear in mind that there are no vent holes in the case, so the motor will likely overheat and fail. Go with something more professional-grade for that type of use, or you could modify this one. As is, this is for short runs only.
I personally use it to mix drink mixes like protein shakes and Gatorade powder and it works great for that. With the Gatorade I start out with 1 quart, let it stir for a half hour, then dilute into the final 2 quart container. It tastes just like store-bought that way. I used to have to wait overnight for the powder to dissolve all the way and take out the bitter flavor that comes from an incomplete dissolution.
For protein shakes, I also can't stand the flavor of grainy undissolved powder, and this solves the problem as well. I mix one scoop in a pint glass full of water and let sit for 20 minutes, occasionally squishing powdery chunks with a teaspoon. The shakes all still taste horrible with the sucralose they all have in my opinion, but this makes them more palatable to me. Cleanup is easier than a blender too, and you make fewer dishes this way, since you're dropping a tiny stir bar into the container you drink out of. That's all you have to clean other than the glass you're mixing in. I plan to order a few more stir bars so I don't have to hand wash them every time.