About
All feedback (139)
- thinkpan (259186)- Feedback left by buyer.Past yearVerified purchaseGood buyer, prompt payment, valued customer, highly recommended.
- tagmil (24433)- Feedback left by buyer.Past yearVerified purchasequick and easy, excellent providence plantation state ebayer
- pleaserewindadmin (69859)- Feedback left by buyer.Past yearVerified purchaseGreat Buyer, thank you!
- *****- Feedback left by buyer.More than a year agoVerified purchaseGreat communication. A pleasure to do business with.
- ta-315529 (225)- Feedback left by buyer.More than a year agoVerified purchaseGood buyer!
- llcostom (2230)- Feedback left by buyer.More than a year agoVerified purchaseFive star buyer! Quick payment and smooth transaction! A+.
Reviews (3)
Jun 21, 2021
OK, Not Terrific
It's OK, not "terrific." The reason is that it is slightly larger than the part it replaced. The result is that when you are typing, the upper keyboard cover edge protrudes past the edge of the bottom part of the laptop case. Since the edge is sharp, it's easy to scrape or cut yourself if you do not first sand or smooth the edge somehow. The mismatch in size also makes snapping the cover in place difficult, because the plastic latches don't exactly fit. The palmrest buckles slightly when pressed back in place. I can't imagine how hard it will be to remove it if necessary. Although until it finally locked in place, it was bowed over the mating surface and did not seat properly. After some fiddling, it finally fits, but by no means like what you would expect from a factory part. The price is acceptable for this level of quality, however, so it serves the purpose (mine was replacement of a worn touchpad and poorly-functioning mouse buttons), although the mouse buttons really aren't any more responsive than the ones on the old palmrest.
May 28, 2019
Doesn't work - too loose
I bought these for my Dell Latitude to replace the rubber cap on the pointing stick. They weren't even close to fitting; placed on the stick, they were so loose that you would move the rubber cap, but the stick underneath would stay in place. Removing your finger would remove the cap, just by the adhesion to your finger. It just plain did not fit. It is also made of a material inferior to the original cap - a harder plastic.
Feb 23, 2021
Does not work on B320
This positively will not fit a Lenovo B320. The B320 has a cradle that fits in an open slot in the back of the computer, precisely sized for the 3 1/2" drive supplied with the computer. ALL 3 1/2" SATA drives have their SATA connectors at the bottom corner of the drive edge, and that is where the solidly mounted SATA socket is, within the slot in the back of the B320 computer.
The 2 1/2" drive carrier shown puts the SATA connector of the 2 1/2" SSD in the middle of the carrier. Whether placed in the Lenovo cradle or in the slot by itself, this puts the connector in the wrong place to enter the socket of the SATA interface in the computer.
I have just gone through installing a 2 1/2" SSD in a B320; I had to mount it in reverse, cut excess sheet metal off the 2 1/2" drive carrier, and use an 8" SATA extension cable that plugged onto the drive, wrapped around the inside of the Lenovo cradle, and plugged into the Lenovo SATA socket.
To say that this drive, as shown, will fit a B320 is false advertising; it cannot in any way fit a B320 Ideacentre computer.
While you can plug a 2 1/2" SSD without a carrier into the Lenovo socket, there is then no support whatsoever for the drive, nor attachment mechanism; you would have to fabricate a metal drive bay for the SSD and drill into the Lenovo frame, or duct tape the drive in place, which would cause it to overheat.
ideacentre B320s were NOT made to accommodate 2 1/2" SSDs without major fiddling to anchor them within the designated area. Open up the back of the computer and see for yourself before ordering.