The brackets work great. Helps the double din fit nice and snug. The trim piece is so so. Doesn't actually cover the alterations you have to do to the dash to make a double din fit. One side fits s lil tighter then the other. But way cheaper then buying a new dash designed for a double din.
Verified purchase: Yes | Condition: New
It looks so promising! And yes, I knew the dash would need cut. It came with instructions on where to cut. That's not the problem. The problem is the face plate cover was long and too short. : I was still able to use it but see pictures. : For the face plate it came with: - I cut off the 4 clips (They looked like they should clip in to the dash but did not and ended up in the way). - I cut off the left and right sides (removing the top and bottom skinny peices leaving the "ears"). - I used these two peices to close the exposed gaps. See green arrows. ------- Dash Mod: - Note the red lines on photo of dash / radio. - I cut out a notch for the USB port. - The top needed the most cutting. - I used a small detail saw to do this. - I tried to sand it smooth. - I then took a small blow torch to heat the edges and attempted to round the harsh angles the cuts made by using my fingers while it was still hot / soft. (Mr Obvious says be careful if you try this too!) ------- For the radio: - I ended up keeping the 2 dim radio behind the original dash so it's pushing from the inside out against the original dash (not protruding out of original dash peice like most aftermarket radios would). - The mounts it came with worked great for this without modifications. - I used the two peices marked with the green arrows to close in the holes. (I should have made a bracket and attached them flush to the radio front but I glued them inside the dash and that is why the left side has a small gap) ------ Bonus Tip: I put in another cigarette lighter port (bottom left) and attached the hot wire to the radio power so now when i shut off the key, my dash cam doesn't drain the battery)Read full review
Verified purchase: Yes | Condition: New
First of all I ordered this mainly for the radio brackets as I plan to modify my dash bezel without needing the facia trim ring. In the meantime however it works great and still looks good! I did not have to modify the radio rear support as it says in the instructions, if you peel the foam off the support and leave the brackets a little loose you can slide the stereo all the way in and mark the brackets then line up your brackets to the marks and tighten down and slowly slide the stereo back in. It fits tight but it should fit! Of course if you don't care then hack the rear support and don't worry about it! I didn't want to modify the actual dash any more than absolutely necessary and so far I haven't other than removing the foam tape. Yes I am doing a dash swap to replace my broken dash so I had it easy if I needed to modify the dash but would rather leave as much support as I can so this dash has a chance to last!Read full review
Verified purchase: Yes | Condition: New
very easy to install great fit for older chev trucks
Verified purchase: Yes | Condition: New
I did not end up using the install kit-just the harness, clips and antenna adapter-while having everything apart I realized that cutting out the old panel to install this over it would never have looked as nice as I would have liked. The profiles were not the same at the top curve. Ended up buying a new double din panel which worked well.
Verified purchase: Yes | Condition: New
Clips in nice and tight into factory slides. The trim piece is just cheap plastic.
Verified purchase: Yes | Condition: New
Did not fit my 99 silverado and the shop threw it away because the dash panel piece had to be cut and I pulled my truck out of the shop getting fixed and now my dash panel has a gap in between the radio and the dash panel now I have to get a replacement panel to replace my original piece.
Verified purchase: Yes | Condition: New
This worked perfectly on my Pioneer ddin stereo. Had to cut out the metal dash support in my 01 GMC 2500 HD to put in a double din, but this kit made installation easy!! Highly recommend.
Verified purchase: Yes | Condition: New
good kit but would have helped to have screws included for mounting to radio. Had to try and find screws to mount with. Holes didnt line up the best either but made work. front trim cover did not work with my installation. Might just be the radio I used it on was not quite compatible. otherwise it did work as it should and slid right into factory latches.
Verified purchase: Yes | Condition: New
Ordered this kit to install a 2 din stereo in a 2000 Silverado in which it was not intended for and it worked great. I use the wide pieces of the trim for filler pieces and epoxied them to the inside of my original trim panel. The rest of the parts are the same and worked great.
Verified purchase: Yes | Condition: New
Current slide {CURRENT_SLIDE} of {TOTAL_SLIDES}- Best Selling in Other Interior Parts & Accessories
Current slide {CURRENT_SLIDE} of {TOTAL_SLIDES}- Save on Other Interior Parts & Accessories