I bought this exhaust mid 2018 and am writing this review January 2020. Pro's - Welds are great - Sound is very good - Can't beat the price Con's - Fitment is not perfect! Do not expect this to bolt on with no issues. ~ It touched one of the cross members and vibrated badly; solution was to hammer a dent into the pipes. ~ The hangers do not put the mufflers in the right area. - Supplied clamps and hardware were not sufficient; bolts broke, clamps failed, or the clamps could not tighten down enough to keep the joints from moving. - The expanded slip joints were WAY too big. It was VERY difficult to keep the mufflers from losing position. - The right side muffler section was in two pieces, this made it even more difficult to maintain it's position. - The rear mufflers are 2.5" inlet, dual 2.25 outlet. The size is fine, but the internal routing is shaped like an "h". This makes it so the "straight through" tip is the only one that gets soot on it. Ideally, I would have liked to see 2.5" in and single 2.5" out. Then supply "Y" pipes and the four tips. This would allow the installer to adjust the tips any way necessary. - The exhaust tips are welded on. Clamped on tips would've helped in getting everything lined up. It would have also been nice when... - The exhaust tips are RUSTING. Because they are welded on, I will need to remove the exhaust, cut the tips off, and HOPEFULLY there's enough piping left to clamp on another set. If I didn't have to dent the pipe and now have to cut the tips off and deal with the odd flow I would recommend this setup to someone willing to deal with the other issues. It does sound great with my headers though!Read full review
Verified purchase: No
It fits awesome, welds are clean and it sounds really good with headers. Just the down pipes alone from IE or CTS is nearly the price of this full exhaust, and it includes the downpipes. My only issue was it had no clamps, or hardware which is deceiving since it says it comes with them and there is a picture of some clamps. It was a major hassle to try and go to multiple stores to find enough clamps for the job.
Verified purchase: Yes | Condition: New
I bought this exhaust mid 2018 and am writing this review January 2020. Pro's - Welds are great - Sound is very good - Can't beat the price Con's - Fitment is not perfect! Do not expect this to bolt on with no issues. ~ It touched one of the cross members and vibrated badly; solution was to hammer a dent into the pipes. ~ The hangers do not put the mufflers in the right area. - Supplied clamps and hardware were not sufficient; bolts broke, clamps failed, or the clamps could not tighten down enough to keep the joints from moving. - The expanded slip joints were WAY too big. It was VERY difficult to keep the mufflers from losing position. - The right side muffler section was in two pieces, this made it even more difficult to maintain it's position. - The rear mufflers are 2.5" inlet, dual 2.25 outlet. The size is fine, but the internal routing is shaped like an "h". This makes it so the "straight through" tip is the only one that gets soot on it. Ideally, I would have liked to see 2.5" in and single 2.5" out. Then supply "Y" pipes and the four tips. This would allow the installer to adjust the tips any way necessary. - The exhaust tips are welded on. Clamped on tips would've helped in getting everything lined up. It would have also been nice when... - The exhaust tips are RUSTING. Because they are welded on, I will need to remove the exhaust, cut the tips off, and HOPEFULLY there's enough piping left to clamp on another set. If I didn't have to dent the pipe and now have to cut the tips off and deal with the odd flow I would recommend this setup to someone willing to deal with the other issues. It does sound great with my headers though!Read full review
Verified purchase: No
Current slide {CURRENT_SLIDE} of {TOTAL_SLIDES}- Best Selling in Exhaust System Kits
Current slide {CURRENT_SLIDE} of {TOTAL_SLIDES}- Save on Exhaust System Kits