CURRENTLY SOLD OUT
About this product
Product Identifiers
BrandToro
MPNLAK-99-9313
UPC0685650083209
eBay Product ID (ePID)13029955192
Product Key Features
Power SourceNot specified
ColorBlack
California Prop 65 WarningThis product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
TypeNot specified
Ratings and Reviews
Most relevant reviews
- Jun 13, 2019Top favorable review
Great product, perfect fit.
Fit like a glove, all holes in right locations and size. Took maybe 15 minutes to install. Can't comment on wear, it's June here in Wisconsin. I had bought a different set on here that when arrived, were thicker than OEM. At first I thought great, these will wear like iron. Only problem, the bolt holes were too small, I drilled them out only to find bolts were to short to fit thru the thicker rubber. I should have realized this right off since the left side lower bolts are always a problem to start with. I worked for a whole day trying to get them to fit, wrecking two bolts in the process, So in this case, bigger is not always better. If these wear like I think they will, they will be a home run.Verified purchase: YesCondition: New
- Jan 16, 2022Top critical review
Would not recomend
These paddles are much thicker and of a different and much stiffer material than the oem ones are. I was able to get the upper bolts in with difficulty and the use of vice grips to hold the paddle in place but there is absolutely no way to get the already difficult lower bolts back into it to hold the paddle in. The material is just too thick and stiff and there is no room to clamp with a vice grip to hold in place while you try to screw/bolt. The other issue is the paddles I received brush up too tight against the inside of the snow blower body in the back. It will not turn it's too wide. It seems like I would need to trim some of off the entire length. I would not recommend these for the Toro CCR 2000.Verified purchase: YesCondition: New
- Jan 24, 2022
Very difficult to install. Not like OEM. Not worth the savings
These paddles are made of a thicker and much more rigid material than OEM. They were near impossible to install on the machine because they would not bend enough to get the outside bolts to line up. I had to dunk the ends of the paddles into hot water and use a heat gun to give them enough flexibility to install. Even then it was still very difficult to line them up and get a nut on the other side of the bolt in tight quarters while pushing as hard as you could to keep the bolt in the paddle through the hole on the blower. Also the holes that were punched for the bolts are to small to fit the bolts. Before heating, I had to use an arbor press to press the bolts through the paddle and to push the center metal rings in. Even then they would pop back out while I was installing and I had to push back in with a large pair of channel locks. They struck the inside of the snow blower badly enough that they would not turn. I had to trim them a bit and finally the machine could spin them. The machine spit out paddle material for several minutes until they were at the correct clearance. They are installed now and I am sure they will work just fine, but not worth the hassle.Verified purchase: YesCondition: New
- Jan 25, 2022
Not a direct replacement but working fine.
These were not a direct replacement, as others have mentioned they were much thicker than the originals. The holes were also the wrong size. If you're not comfortable modifying things and have some hardware on hand they can be made to work but you will be spending some time massaging them into place. In the end, after an hour or so of drilling, clamping and replacing the original hardware since it was too short to make it through the new rubber, the machine is up and running and they seem to perform well. Bottom line is if you want a quick swap, buy the real thing. If you're not in a hurry and ok modifying things, go ahead and save a few bucks with these.Verified purchase: YesCondition: New
- Oct 31, 2020
Toro rubber paddles
Was a great replacement! They fit with no problems although they were missing a bolt hole on each one. Wasn’t a big deal, I just drilled the hole in each one after mounting them. It probably would of been fine without them but, had the bolts and time to put them in. Will buy again if I need to.Verified purchase: YesCondition: New
- Aug 27, 2019
I would recommend the paddles very highly
Material looks great, fit was perfect. Very pleased.Verified purchase: YesCondition: New
- Nov 02, 2021
Toro-CCR2000-CCR2400-CCR2500-CCR3000-Snowblower-Replacement-Paddles-99-9313/165102582719
These are far more durable looking than OEM paddles. It take some serious massaging to get them installed. But they work perfectly.Verified purchase: YesCondition: New
- Mar 04, 2019
Great quality and very reasonable price
Very durable for it's intended use and great price!Verified purchase: YesCondition: New
- Nov 12, 2019
Easy Installation
I replaced worn out blades on my snow thrower with new blades I got. Precise fit. Great prices on the new blades. Genuine Toro blades price is ridiculously double!Verified purchase: YesCondition: New
- Feb 09, 2019
Excellent product and excellent service
Fit my Toro CCR™ 3650 GTS® snowblower. Must reuse metal location sleeves (as most probably do also).Verified purchase: YesCondition: New
