Picture 1 of 4
![Stock photo](https://i.ebayimg.com/images/g/OcAAAOSwNmhfUPDi/s-l640.jpg)
![LEE 90303 LEE 2-CAVITY BULLET MOLD 358-158-RF .358 DIA 158 GR Free Ship - Picture 1 of 4](https://i.ebayimg.com/images/g/WzgAAOSwuOxmZQYu/s-l500.jpg)
![LEE 90303 LEE 2-CAVITY BULLET MOLD 358-158-RF .358 DIA 158 GR Free Ship - Picture 2 of 4](https://i.ebayimg.com/images/g/4xcAAOSwDTJmZQY1/s-l500.jpg)
![LEE 90303 LEE 2-CAVITY BULLET MOLD 358-158-RF .358 DIA 158 GR Free Ship - Picture 3 of 4](https://i.ebayimg.com/images/g/FE8AAOSw1admZQZB/s-l500.jpg)
![LEE 90303 LEE 2-CAVITY BULLET MOLD 358-158-RF .358 DIA 158 GR Free Ship - Picture 4 of 4](https://i.ebayimg.com/images/g/MnAAAOSws7dmZQYh/s-l500.jpg)
Picture 1 of 4
![Stock photo](https://i.ebayimg.com/images/g/OcAAAOSwNmhfUPDi/s-l640.jpg)
![Picture 1 of 4](https://i.ebayimg.com/images/g/WzgAAOSwuOxmZQYu/s-l1600.jpg)
![Picture 2 of 4](https://i.ebayimg.com/images/g/4xcAAOSwDTJmZQY1/s-l1600.jpg)
![Picture 3 of 4](https://i.ebayimg.com/images/g/FE8AAOSw1admZQZB/s-l1600.jpg)
![Picture 4 of 4](https://i.ebayimg.com/images/g/MnAAAOSws7dmZQYh/s-l1600.jpg)
After molding about 500 rounds with this mold and reloading and shooting the loads here are my thoughts about it. I did resize all bullets with a Lee sizer/ lube kit to .358. Some bullets measured slightly over size though that is to be expected. The bullets I molded were .358 diameter 158 grain rnfp. They were all very accurate and worked fine through a revolver and a lever gun. Back to the mold. It is aluminum so the temperature of the mold is important to getting a good bullet. It needs to be preheated before starting to cast. I also smoked the mold before use and resmoked after about 300 casts. The screw that holds the sprue plate on top started to work loose at this point. It was an easy fix by simply re tightening it. This is a great 2 cavity mold although you could save some time casting using a 6 cavity mold. All in all its a great mold and you save lots of money casting your own bullets.Read full review
Verified purchase: Yes | Condition: New
While the original design made great boolits, pin alignment was poor and spru plate frequently needed tightening, making it hard to handle fast. The new design corrects the minor flaws of original. Beveled base is 1/2 the length of original, making these new boolits slightly shorter and lighter than original. Excellent product, dropping 100% keepers after first couple dozen to break it in.
Verified purchase: Yes | Condition: New
I've been casting these for both .357/.38 cartridges and also for my big bore airguns. I have also sized them down to .356 diameter and fired them very accurately out of my 9 mm cartridge guns and airguns. Once you get the mold heated it produces flawless bullets.
Verified purchase: Yes | Condition: Pre-owned
Made several hundred using wheel weights. Shot great out of my Rossi 92 and 357 New Vaquero. Great mold. Remember to smoke it prior to use.
Verified purchase: Yes | Condition: New
Lee products are high quality and affordable. The bullets I cast from the Lee molds are accurate in my guns and easy to cast. I love Lee Molds.
Verified purchase: Yes | Condition: New
Current slide {CURRENT_SLIDE} of {TOTAL_SLIDES}- Best Selling in Molds
Current slide {CURRENT_SLIDE} of {TOTAL_SLIDES}- Save on Molds