Dash Parts. 1x Dash Cover Cap. Seats & Seats Cover. This part will NOT replace a missing bezel. Installation is simple and requires no special tools. The cap is held in place with a high strength, silicone adhesive.
I wish I would have got the nicer one but it was a $100 or more .This one with keep GMC and Chevrolet cheap junk together till I swap for something else. The package that it came was pretty much mashed completely flat . I was worried that it was destroyed. Must be made from Toyota tufff plastic .Good news only had a few scuffs and 2 little indentation. But I’m still happy for the money that I put into a dash cover .but post office is ridiculous with our packages these days! Thanks again
Ok here we go, I read other reviews prior to purchasing this item and I will say that my expectations where definitely high cause I to had dash damage due to the sun's heat, the vehicles vibration, and over all stress at 160,000 miles, how ever when I opened and examined the dash cover I noticed that the manufacturing of this product wasnt really to my over all liking, I say that because around some of edging by the doors R/L flange coming down from the dash vents a razor blade was used to custom cut to its specifications without breaking the edges over needless to say it looked like a cookie cut out, then upon a test fit it scratched up my Bose high speaker close out sides pieces R/L quite a bit more than I realized after it was in, note to self, if you install this be mindful of this issue, but this damage can easily be avoided by taking sand paper to the sharp corners to smooth them over avoiding scratches all together.
Next was that in the manufacturing process they had also used a razor blade to cut part of the vent holes out as well, needless to say I was starting to prefer the cracks in the dash cause of how tacky to me this looked as a presentational piece, if you have this issue as i did you can resculpt your vent hole corners with sandpaper as well to run more along the seem of the vent hole covers.
In some areas minor distortion was present along the nosing of the cover, but I to like another reviewer used a heat gun to shape it to a desired form and it's easily achievable.
Another issue I had was the slotted vent towards the windshield part of this dash cover located in the middle, to me as a cover and not an original part it was unnecessary to go through the trouble to even do this in my opinion, plus I just didnt like the look of it anyways, so I cut mine out and sanded the edges tabs flush, my reasoning for doing this is because this is a 2 part dash assembly, and the secondary piece with the vent in it was not damaged, your might be and you also might want the covers vent addition, I didnt, the only damage i had was to my primary piece, and all my cracks came from the mounting pick ups from under the secondary piece leading to the primary piece, if you've ever popped yours up you'll see where these start from, regardless I was more into the main piece and its simplicity.
Over all I felt that what I was dealing with definitely wasnt what I expected when reading the reviews, so I took it upon myself to wrap it in black vinyl, and to my avail extreme joy came about this project, like seriously, to me this cover makes for a perfect substructure in wrapping it, now I did all these minor modifications knowing I was going to do this in vinyl, otherwise I would have sent it back and delt with the cracks cause I felt it just looked cheap with sharp edges and tacky in what is still a nice truck I have, but wrapping this in vinyl made me appreciate this product alot more than I did when it arrive.
Lastly I chose to opt out of using the adhesive and went with a little adhesive back velcro in a couple corners, it's a dash cover, it's not going anywhere when the doors are shut even with all the windows blow out of it.
I would encourage anyone who purchases this product to understand that with a little time you can make this cover well worth the $70 with some additional attention, this progect took me about 4 hours to do and the vinyl match is spot on with my seats and extremely close to the original dash look, not bad for a Saturday morning.
The product is worth it and priced just right if you know what your doing, if you dont care then so be it, but to all you DIY Interior guys and gals out there this is what your gonna be dealing with if your picky or QA, hope this review and the photos help.Read full review
The idea is great the end result is just ok at best. It took two hours to trim and grind the new dash cover to fit the existing dash cover, which was not that bad just a few cracks. The next problem it that there is not enough adhesive to complete the job. I trail fight the new cover, per the instructions, then applied all of the adhesive, then clamped and taped and applied pressure and let it set up over night. as soon as I released the pressure the new cover stated to curl up and lift most everywhere. My next attempt will be with a better grade and more adhesive. Not at all a fix for a problem cracked dash. Now I get to start over and HOPE it works better next time. Don't waste your time and money on this product
I had to work on the dash cover to make it fit correctly. The corners that are on the the front of the cover were too tight. I'm fairly handy so I took heat gun and softened the corners so that I could reshape them and I also had to us my orbit sander with 120# to work a few edges down. If you don't mind doing these I'd recommend.
This cover is as described. The glue that came with it was slightly insufficient to cover everything that needed to be covered so the cover is not as plastered to the original cover as I would have liked it to be. That being said it looks nicer then the original cover with cracks in it. It is somewhat difficult to tell there is a cover but since u installed it, you could tell that it is a cover but they might not be able to tell. Sorry it was dark when took pics.
The OEM dash is garbage which, I imagine, is why this aftermarket "skin" was made. Order one even if your dash is currently fine as you will need it one day. Doesn't come with any attachment glue which I'm OK with. Just sitting on top now. I do need to attach at some point to get the ends down and eliminate any noise. Thinking of double sided tape or liquid nails. We'll see. The "skin" fits well. Now my only issue is the airbag cover (not provided nor should it be) is faded.
Horrible fit for dash cover. 0/10 would not be ripped off again
Horrible fit, glue included is useless. Product arrived warped and was the farthest thing from a quality dash cover. Save your money and do it right the first time. Get the cover king product.
Doesn't exactly fit all that great on a 2011 Tahoe I had to use a heat gun to reform the ends and to get them to lie down a little better little better the glue they supplied I did silicone and I guess doesn't stick very well But it looks better than it did but for The money it's not too bad
Shipping speed was good the quality of the product being packaged was bad.
Other than that I had to trim some of the edges to make sure it fit snug. Apart from those things the product is worth it.
