10 BLADE LOW WIND Propeller 60" Wind turbine generator with D/THICK HUB 62"

This auction is for a complete blade set including: TEN carbon fiber turbine blades.

INCLUDES: Super tough round steel 10 blade hub, 20 bolts and lock nuts plus instructions.

RECOMMENDED FOR SLANT CORE PMA's FOR TURNING THEM INTO FANTASTIC LOW WIND SPEED AREA TURBINES

(Note: 11 blades is to much "blade area" for SLANT CORE pma's  - 11 Blades was designed for optimum use with POWER CORE and SUPER CORE pma's only)

100% American Made - High Quality Product (Not Imported)

Molded in Garden Grove California and Injected with plastic and fibers made in the USA (SGL, Valencia, CA)

 

Each one of these blades is 28 1/8" long, and almost 6" wide at the base.

 

OUR 10 BLADE SET's ARE THE BEST ULTRA LOW WIND BLADE

KITS FOR USE ON SLANT CORE or older era "CLAW CORE" pma's

(turbine and pole not included)

Photo shows 10 blades mounted (turbine and pole not included)

 

 

 

The microphone in this video was placed only about 12" away from the blades

so you can clearly "hear" the power and spin speed. At distance these blades

are surprisingly quiet and non-offensive to be around. Very neighbor friendly.

---

You are bidding on the MOST powerful high speed blade system on the market today! 

Only blades with thin tips can break the 1700 RPM barrier !!! - 

Build Your Own Wind Turbines with our high speed blade sets! -

   

If you are trying to make wind power using an AMETEK or 90 VDC type motor or any other such device you are going to need a LOT of speed which gives you that special type of ultra quick twisting power that just can't easily be stopped! The tip speed of these blades can reach over 400 MPH during extreme wind gusts. They cut through the air like a BUZZ SAW! Only blade sets with thin hardened tips can break the high power 1700 RPM barrier!!! This assures that you are catching all the wind and that no potential air is slipping past the blades! When you see these blades working you are really going to fall in LOVE with their extreme POWER POTENTIAL! Wind turbines using an AMETEK or other type of DC motor as the power plant perform extraordinarily WELL with this type of blade design that is capable of producing these incredibly fast velocities due to its razor sharp edges. They cut through the wind effortlessly even at tip speeds of 550 MPH+.

 

Larger profile aluminum or wood blades just can't turn fast enough to hit the ultra high speeds many of the home made wind turbines need in order to really put out those heavy duty amperages or high voltages necessary for quick energy.

 

These blades are also VERY forgiving in the event of "fall accidents" and 90% of the time they can hit the ground and never break in the event of tower falls or other such mishaps. MADE of VERY TOUGH MATERIAL! Can be bent at 140 degrees and they will pop right back into perfect shape!

   

---

Letter's From Happy Customers

---

asw??????stlink.ca

 

andrew why????????wrote:

 

Hey Qaz , yes I have a set of your 28" blades which is why I have purchased more from you. I have spent the last year doing R&D in my spare time on various products from you and many other companies on line for small wind and solar. I have a full time electrical company so my time is limited to the winter months. Please understand that I am in no way trying to infringe on your products or your business and the few sales that I would do in the winter time would not even compare to the volume you do. With that being said I hope we can keep the communication between us now that I have your attention. The 29" blades that I purchased from the seller " hi_iq" are: thinner and have a reverse blade tip pitched back the opposite to the base hoping to get the blade to yield away from the tower in higher winds but in fact interferes with the performance of the blade. With your blades my machine starts at 9 mph and quickly speeds up to a blur, with hi_iq's blades on my machine it doesn't start to spin until 14 mph and just sort of "lolly gags around" giving me no charge. I am using 10si Delco remy alternators completely stripped and rebuit from scratch with 1" x 2" N50 magnets in my core which gives me huge power potential but serious cogging issues for the blades to overcome. My resources are limited and am still looking for a cheap supplier of special would stators as I don"t have a stator winder and angling my magnets to overcome the cogging like yours is not an option with those big magnets jammed in that little PMA. On another note I think you need to have a discussion with the sellers that are using your pics of wind turbines to sell theirs, I have noticed you have built up a good rep it would be a shame to let other sellers destroy it by using your famous pics. Anyway I could ramble all night , I have included a pic of my machine, if you have any questions about anything contact me and I hope to do a lot of business with you in the near future.

Thanks asd?????????

 

---

Dear qaz661,

Love these blades you were right, wow can they turn on, im getting up to 40
volts out of my indiana general dv pm motor,there scarey sometimes, im
putting it on youtube for all to see, thanks again

-uptick57

Dear qaz661,

I just want to brag about your blades and PMA, I live here on a mountain
top in Idaho, and had freezing temps. Then came the high winds, the 12 volt
PMA maxed out over 75 volts and the blades held together with wind gusts
over 50 MPH. What a great product. I just need a controller that won't
smoke with these high wind surges, what do you recommend?

Thanks Sonny

-ljdk07

---

 

 

NEW-AGE

Americana

 

The New Look Of

American Suburbia

 

---

---

Notes from OTHER Happy customers:

Date: Thu, 27 Apr 2006 22:35:00 EDT
From: SANDCRE???9aol.com
To: inf?cu2.com

Dear Bob:
I thought I would drop you a line and let you know about the turbine I ordered from you, it was to replace a southwest wind power windseeker 503, because it continually trashed the blades, I have gone through three of their sets of blades, and now they stopped making and servicing them. As I was assembling the one I received from you the windseeker was on the bench right next to it, and just for the heck of it I thought your hub and blades might go on the windseeker, which it did, I remounted the wind seeker with your hub and six blades and never saw it do such a good job, for nine years I have been hiding from this thing, and now I can stand right underneath it, your advertisement on your web site is 100% truthful, your blades turn with very little wind, and they withstand very high winds, and make very little noise, and virtually no vibration. I would recommend your blades to anybody that wishes to improve their current Wind Chargers. I haven't had a chance to mount your wind turbine yet as I am waiting on another set of blades. And if anybody wants to know about your customer service, I would highly recommend them to you, you always answer your e-mails and are very helpful.
thank you
R.S.
Colo

---

Dear qaz661,

 

Bob, these blades are awesome. I've started installing a few PMAs, running
2 here at home, for outback and rural location applications in Michigan.
I've been in the auto industry for 30 plus years and think I've found my
second calling. Thanks for a great product. Future business with you is a
given... Thanks Again!!!

 

-windgenworld4092