5/8 Inch Arbor For Wind turbine Generator Hub has 17mm thread fits 5/8" shafts

FREE SHIPPING TO THE LOWER US 48 STATES

YOU ARE BIDDING ON ONE WIND TURBINE HUB ADAPTER /17MM THREAD X 5/8'' MOTOR SHAFT

THIS IS THE ORIGINAL MADE BY MISSOURI WIND AND SOLAR

THIS HUB ADAPTER WILL FIT ANY HUB WITH A 17MM CENTER HOLE AND

THEN GO ON YOUR 5/8' MOTOR SHAFT LIKE AMETEK AND OTHERS.

WE NOW HAVE 3 SIZES OF HUB ADAPTERS
 

MADE FROM HIGH QUALITY STEEL WITH A HIGH TENSILE STRENGTH (NOT CHEAP ALUMINUM)

17MM  25TPI FINE THREAD (NOT 1/2'' COARSE THREAD THAT WILL LOOSEN)

5/16'' ALLEN SET SCREWS FOR REAL TORQUE (NOT TINY SET SCREWS THAT CAN'T BE TIGHTENED)

OURS ARE GOLD ZINC PLATED, WON'T RUST!!!!!! (ALUMINUM WILL OXIDIZE AND SEIZE TO A STEEL SHAFT)

DESIGNED AND MANUFACTURED BY A MILITARY CONTRACTOR

WILL LAST A LIFETIME,AS HEAVY DUTY AS YOU CAN GET   

(LIFETIME WARRANTY)

WE MAKE OUR PRODUCTS WITH YOUR SAFETY IN MIND!!!!!!!!!

MADE IN THE USA BY MISSOURI WIND AND SOLAR

NEVER USE AN ALUMINUM HUB ADAPTER THEY OXIDIZE AND SEIZE TO A STEEL SHAFT THEN THEY POWDER AND COME OFF,EVERYONE KNOWS THAT YOU DONT PUT STEEL TO ALUMINUM IT OXIDIZES.WHEN ALUMINUM COMES IN CONTACT WITH STEEL IT CAUSES A CHEMICAL REACTION .A 1/2'' COARSE THREAD IS TO SMALL FOR THE STRESS ,ALUMINUM CAN'T TAKE THE STRESS AND WILL CRACK,A COARSE THREAD WILL NOT HOLD THE NUT ON,IT WILL LOOSEN AND COME OFF.WIND TURBINES HAVE ALOT OF VIBRATION AND ALUMINUM CAN'T TAKE VIBRATION LONG BEFORE IT BREAKS,SAME GOES FOR AN ALUMINUM HUB!!!!

DO NOT TRY TO SAVE MONEY ON A HUB OR HUB ADAPTER,

THE FAILURE OF EITHER CAN BE DEADLY!!!!!!

NOW YOU CAN USE A HUB WITH A 17MM HOLE CENTER FOR YOUR 5/8'' MOTOR SHAFT

VERY FINE THREAD ON OUR 17MM SHAFT,NUT WILL NOT LOOSEN AND COME OFF LIKE COARSE THREAD WILL.

OUR HUB ADAPTER WILL FIT RAPTOR HUBS,HORNET HUBS,WIND SCORPION HUBS AND ALL HUBS WITH 17MM CENTER HOLE.NOW YOU CAN USE REAL TURBINE BLADES AND HUBS THAT THE BIG BOYS USE!!!

VISIT OUR EBAY STORE FOR ONE STOP SHOPPING ON WIND AND SOLAR PRODUCTS   YOU ASKED US WHERE OUR WIND TURBINES HAVE BEEN INSTALLED AND WE THOUGHT WE WOULD SHOW YOU.

The pictures below show a Suzlon wind turbine in Denmark with a Missouri Wind Turbine 

mounted on top.Suzlon made it clear they needed dependable wind turbines to operate the beacons.

After months of testing they decided to go with a wind turbine built in the USA

by Missouri Wind And Solar.Notice the MW logo on the tail fin.

100% Manufactured in Seymour Missouri,The Show Me State!  

 






 OUR MISSOURI WIND TURBINES ARE TUFF ENOUGH FOR SUZLON, HOW ABOUT YOU?

The diagram below shows a typical wind setup using

parts from Missouri Wind And Solar 

 

 

INSIDE OUR STORE MISSOURI WIND AND SOLAR IN SEYMOUR,MISSOURI

A REAL STORE WITH REAL PEOPLE 

YOU CAN ACTUALLY COME IN AND TRY OUR PRODUCTS AND SEE THEM WORKING

WE  ANSWER THE PHONE AND OUR EMAILS