This is USED KORG MS2000 MS 2000 /
Hi there This is USED KORG MS2000 MS 2000 /
The function works perfectly,
This comes with the softcase
Check it on the picture
You need the adapter
.The adapter spec is Center Minus 9V 500m adapter
You can easly find them on ebay
The condition is near mint to mint
Here is English Manual
Sounds are initiated in the MS2000 in a somewhat standard synthesizer manner, and then routed in various ways to produce the final sound. All sounds (timbres) in the MS2000 consist of the following steps and path: OSC1/OSC2/NOISE, MIXER, FILTER, AMP, EG, LFO, VIRTUAL PATCH, MOD SEQUENCE, EFFECTS and ARPEGGIATOR. If the voice mode is Single, only TIMBRE 1 will sound. If the voice mode is Dual or Split, both timbres TIMBRE 1 and TIMBRE 2 will sound.
OSC1 (Oscillator 1) allows one to select from eight different oscillator algorithms, including basic analog synthesizer waveforms such as SAW and PWM, Cross Modulation, and Korg's proprietary DWGS (Digital Waveform Generator System) originally developed for the Korg DW-8000synthesizer. A signal such as a mic, instrument or line input from the AUDIO IN 1/2 jacks can also be processed.
OSC2 (Oscillator 2) allows one to select from three types: SAW, SQU, and TRI. It can also be used as an oscillator for the Sync or Ring modulation.
NOISE (Noise Generator) produces white noise which can be used for sound effects and introducing harmonic distortions to waveforms. The 64 single-cycle, wavetable-like internal waveforms that can be used in the oscillator 1. Taken from mid-80's Korg DW-8000 synthesizer, these waveforms allow the creation of bell and electric piano-like sounds. Also, ring modulation and sync are available as modulation sources to generate sweep and vintage lead sounds.
Used for adjusting the levels of OSC1, OSC2 and NOISE. The combined signal is then sent to the FILTER.
The FILTER cuts or emphasizes frequency components of the signal from the oscillator, affecting tone and brightness. Three primary types of filtering are available: –12 or –24 dB/oct LPF (Low Pass Filter), –12 dB/oct BPF (Band Pass Filter), or –12 dB/oct HPF (High Pass Filter). Using EG1 to create time-variant changes in cutoff frequency adds a fourth type of filtering.
The AMP stage consists of AMP (Amplifier), DIST (Distortion), and PAN (Panpot). AMP sets the volume, and PAN sets the sound's location in the stereo field. Using EG2 can create time-variant changes in volume. Quite harsh tones can be created by turning DIST on, and adjusting the filter cutoff and resonance, higher-pitched rings and tonalities are created with various harmonics layered on.
The Envelope Generator applies a time-variant change to each timbre parameter. On the MS2000/MS2000R, there are two standard ADSR EG’s for each timbre. EG1 is assigned as the envelope source that produces time variant changes in the FILTER cutoff frequency, while EG2 is assigned as the envelope source that produces time variant changes in the AMP volume. The MS2000's VIRTUAL PATCH module can be used to assign EG1 and EG2 to other parameters.
The LFO (Low Frequency Oscillator) applies cyclic change to sound parameters. The MS2000/MS2000R provides two LFO’s for each timbre, each with four waveforms. LFO1 is assigned as the modulation source for OSC1. LFO2 is assigned as the modulation source for the pitch modulation controlled by the modulation wheel. As with the EG's, VIRTUAL PATCH can be used to assign LFO1 and LFO2 to other parameters.
VIRTUAL PATCH allows the use of not only EG or LFO, but even keyboard velocity (keyboard playing dynamics) or keyboard tracking (the area of the keyboard that is played) as modulation sources which can be assigned to sound parameters for greater freedom in timbre editing and sound creating. Four routings (combinations) can be specified for each timbre.
MOD SEQUENCEMOD SEQUENCE is a step sequencer that lets you apply time-variant change to various sound parameters in a way similar to analog synthesizers of the past. The sixteen knobs on the main panel can be used to set the value of each step and then the sequence is played back. The sound can be further modulated by the arpeggiator and by VIRTUAL PATCH. The knobs can also be operated in realtime, and their movements (parameter values) recorded in each step (Motion Rec function). Since each timbre can have up to three sequences, very complex tonal changes can be obtained.
Each program can have a modulation effect, chorus, stereo delay, and equalization. For a modulation-type effect, select from chorus or stereo delay.
The onboard arpeggiator has six types of arpeggio. For a program whose voice mode is Dual/Split, arpeggios can be played on one or both timbres. Since arpeggiator settings can be made for each program, arpeggio types that are suitable for the sound of a particular timbre can be saved and played.
MS2000/MS2000R. In 2000, Korg introduced the MS2000 and MS2000R, the latter being a rack-mounted version of the MS2000. The MS2000 is a 44-key keyboard with modulation and pitch-bend wheels, two analog inputs and two analog outputs, all via 1/4" TRS connections and MIDI IN, OUT and THRU connections. The case was painted a dark teal blue color and sided with mahogany rails. In addition to its body, the signal path and parameter list was silk-screened on the face (MS2000 model only), a retro nod to analog synthesizers of the 70's and 80's. A 19" rack version was simultaneously released, with a designation of "R" added to the name.
MS2000B/MS2000BR In 2004, Korg re-released the synthesizer with some minor changes. The new version was dubbed the "MS2000B", the "B" designation given due to its dark grey/black painted body. A few additional patches and demo programs were loaded, but the most significant improvement was the inclusion of a microphone which could be inserted into the new mic input that was added to the top of the keyboard to facilitate easier use of the vocoder. An identically-capable rack version was also released, with the appropriate "R" designation in the name. It did not come equipped with the mic or mic input, but the vocoder could still be used via one of its audio inputs.
Specifications and options
Tone generation system
Analog modeling synthesis system
- Synth programs: Multi-timbral capability: maximum two timbres (for Split/Dual), 4 voices, 2 oscillators and a noise generator, EG x 2, LFO x 2, virtual patch x 4, MOD sequence (maximum 16 steps x 3)
- Vocoder programs: 4 voices, 1 oscillator + noise generator, EG x 2, LFO x 2, 16 channel vocoder, adjustable level and pan for each channel, Formant
- DWGS (Digital Waveform Generator System)
- FM Synthesis is also possible via Virtual patching
- 2 Timbres per patch, can mix synthesis types
- 4 voice, 2 oscillator + noise generator (Single mode)
- 4 voice, 4 oscillator + 2 noise generator (Dual mode, can also be unison).
- 4 voice, 4 oscillator split mode
- 1 voice, 4 oscillator monophonic mode (can be combined with unison)
Keyboard (MS2000 only)
- Modulation effect (3 types), delay (3 types), equalizer
- 6 types
- Programmable with sequencer
- 16 programs x 8 (total 128 programs)
- AUDIO IN 1 jack: Input impedance 39 [kW]; Maximum input level: –3.5 [dBu] (AUDIO IN [1/INST] knob: Max); Source impedance 600 [W]
- AUDIO IN 2 jack (with MIC/LINE switch):
AUDIO IN 2 [LINE]: Input impedance 39 [kW]; Maximum input level: –3.5 [dBu] (AUDIO IN [2/VOICE] knob: Max); Source impedance 600 [W]
AUDIO IN 2 [MIC]: Input impedance 22 [kW]; Maximum input level: –33 [dBu] (AUDIO IN [2/VOICE] knob: Max); Source impedance 600 [W]
- L/MONO, R jacks: Output impedance 1.1 [kW] (MONO: 550W); Maximum output level +6.5 [dBu]; Load impedance 100 [kW]
- Headphone jack: Output impedance 10 [W]; Maximum output level 35 [mW]; Load impedance 33 [W]
- ASSIGNABLE PEDAL jack
- ASSIGNABLE SW jack
- 16 character (8 ´ 5 pixel) ´ 2 line LCD module (with backlight)
- MS2000: 737.8 (W) ´ 371.3 (D) ´ 147.7 (H) mm
- MS2000R: 482.0 (W) ´ 233.2 (D) ´ 87.1 (H) mm (5U rack space)
- MS2000: 7.1 kg
- MS2000R: 2.8 kg
- AC adapter (DC9V)
- Washers ´4, Bushing ´4, Screws ´4 (MS2000R only)
- EXP-2 expression pedal
- XVP-10 EXP/VOL pedal
- PS-1 pedal switch
- DS-1H damper pedal
We know there are many sellers who do not understand guitars. But do not worry about it . We are experts for musical instruments and our professional guitarist or keyboard player checked the condition.
If you have a question, feel free to ask it
And If you want to buy not only other rare musical instruments but also products in Japan , contact us. Most of Japanese people can not ship them to foreign countries and can not communicate with you using English well.
Our business is to find it and get some handling fee from you! Like 10% of total amount fee .And we also can negotiate with these sellers too. So it is really good deal for you!
1 Paypal (it must be verified)
(we will ship our product to verified address in paypal)
2 Bankwire transfer
( you can choose banks in Japan or USA)
Winning bidders must pay for items within 5 days.
The item will be shipped for 3 days after payment is received.
If you have any questions or require additional pictures or information, please contact us before the auction ends.
Also if you buy some products from us you can combine them with others and can get the discount shipping fee
Terms of Sale
We offer 14-day money back guarantee for defective products
However the buyer must pay money for returning it back to us
Duty and Tax
We never charge you Japanese comsumption tax.
But Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyer’s responsibility.
It is up to your customs, ask them
Invoice and value
We usually write the 30%-50% value of your purchasing price for a private customer
We Also write the value on the invoice as you wish
But you must have the responsibility for it
If you buy new product including the demo unit from us, we will give you manufacture warrnaty for 180days .
And then you must ship it back to us and you have to pay moeny for the shipping fee
If you buy the used product
Hey we are the enterprenur company by Japanese young people.
Our business is to export products and to import products .
Many foreign people only know Japanese good products are electronic products and samurai, anime or something like that .
But we do not think they are all we can supply for the global market.
We also know you can see Japanese Food, culture and fashion in your country , however we are not satisfied with them and know more shophisticated things. Because of them, many foreigners misunderstand what the Japanese real one is !! It is what we are really worried about.
Unfortunately Japanese people are really introverted and shy because we are really big economic country and do not need to be involved in other countries unless someone forces people to do that. Besides as you know most of Japanese people can not speak in English well, for the reason and it is harder to find experts of these fields. Also we usually can not show "YES or NO" clearly from daily communication to the deplomaitc issue. That is why we fail to succeed in many worldwide business.
But we can say our products are always great and great price
Finally if you have a question about Japanese things from culture, travel, to economy politics, feel free to ask them to us
Also if you have a plan to export something from Japan and need a partner, contact us. We will work for it!!!
You can also contact us using them
Skype name is greatjapaneseguy!
Enjoy our auction!
International Buyers - Please Note:
・Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyer’s responsibility.
・Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.
・These charges are normally collected by the delivering freight (shipping) company or when you pick the item up - do not confuse them for additional shipping charges.