This amount includes applicable customs duties, taxes, brokerage and other fees. This amount is subject to change until you make payment. For additional information, see the Global Shipping Program terms and conditionsThis amount includes applicable customs duties, taxes, brokerage and other fees. This amount is subject to change until you make payment. If you reside in an EU member state besides UK, import VAT on this purchase is not recoverable. For additional information, see the Global Shipping Program terms and conditions
New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is
applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details.
See all condition definitions- opens in a new window or tab
... Read moreabout the condition
With Two High contrast Meters (both Volts and Amps)
Two D/C breakers/disconnects.
Fully wired, ready to go for both wind and solar.
Works directly with 12, 24 and 48 volt systems
Use this controller to regulate and prevent battery overcharge in:
Solar Systems,Wind Systems,Hydro Systems
Some of the key features of this controller are:
Microprocessor controlled -- This is very important for both stability and functionality.
User changeable settings -- Several controllers on the market set the dump level, and that's that!
Super High amp rating - 440 Amps -- 10,000 watts. -- Uses the same relay as the SEA-440.
Works directly with 12, 24 or 48 volt systems. -- The relay contacts can handle open collector voltages of up to 120 volts.
High Contrast LED battery voltage. - Several controllers do not tell you what's going on - This one does!
High Contrast LED turbine amperage meter.
Meters can be shut using the on/off switch.
Two factory installed, fully wired D/C breakers and disconnects.
Entire unit is wired and ready to go for both wind and solar.
Battery status LED
Push to test. -- Ever wonder if your controller & load are working OK?
Large (8" x 12") solid steel enclosure, with multiple conduit knockouts
Large enough terminal blocks that you can actually terminate large wire (See notes below.)
The electronics are fully isolated from the enclosure, no ground loops.
Draws almost no energy while monitoring (all electronics must use some power, to work -- this is a miser)
Reverse Polarity protected.
Some specifics about the points made above.
The microprocessor is the heart of the controller. It is given the battery voltage and the user changeable trip points. This information is analyzed and acted upon.
The Battery level is checked, and based on that info, the Green LED flashes or is illuminated as follows
(One) Flash indicates the battery is less than 12 volts (12 volt system - Double for 24 etc)
(Two) Flashes indicates the battery is 12 to 12.5V
(Three) Flashes indicates the battery is 12.6 to 13v
(Four) Flashes indicate the battery is 13.1 to 13.5V
( Five) Flashes indicates the battery is above 13.5V but less than 13.9V (Settings are adjustable)
Steady green means the battery is full.
The red LED is illuminated when the battery is being dumped at 14.5v (or the charge source diverted.)
The dump remains active for a minimum of 5 seconds, at which time it is checked by the microprocessor. If battery voltage drops below the "Dump Cancel " level, the dump is disabled, otherwise the dump is continued and rechecked every 5 seconds.
When you click the "TEST" push-button - the 5 second cycle is started (one time, unless the batteries are within the "Dump Start" and "Dump Cancel" zone.)
Settings are user changeable! By simply turning a simple potentiometer with a small screwdriver, you can quickly adjust the trip point.
High amp rating -- 440 Amps! -- 10,000 watts!! -- This is a MONSTER controller.
This controller is capable of handling the input from 166, 60 watt solar panels, or 10, 1000 watt wind turbines, or any combination of the two not to exceed 440 amps, 10,000 watts. This is a lot of control.
About load diversion.
Several schools of thought on the subject.
The source of power (wind turbine, solar panels etc.) -- should remain connected to the batteries while the dump is active.
The source should be diverted to the load directly and disconnected from the batteries.
We happen to believe that is far better to leave the wind turbine connected to the batteries at all times. Why? When you remove the battery level voltage from a wind turbine and send its power directly to a load, then it sees for all practical purposes a short circuit (depending on the resistance of the load and lead wires.) This may cause the turbine blades to slow dramatically and in some cases bring it to a halt. This braking action can cause heat build up in the stator if it is repeated every few seconds or so (if the battery is just a little over the top). When you allow the turbine to see the batteries, along with the load, the turbine remains more within its design realm -- always a good thing.
The internal relay is configured to dump the batteries along with the source, but if you desire to disconnect the source from the batteries and send it to the load directly, simply utilize the N/C contacts of the relay as well. We'll be happy to send you a diagram -- this is a very simple to accomplish.
** 150 amp heat activated breakers have been installed to limit continuous current to 150 amps. Instantaneous current handling of this unit not to exceed 440 amps. **
Ready to go. built to last, right here in the USA.
below photos show the HVA Charge Controller with
optional dump load, disconnect, inverter and fuse
YOU ASKED US WHERE OUR WIND TURBINES HAVE BEEN INSTALLED
AND WE THOUGHT WE WOULD SHOW YOU.
The pictures below show a Suzlon wind turbine in Denmark with a Missouri Wind Turbine
mounted on top.Suzlon made it clear they needed dependable wind turbines to operate the beacons.
After months of testing they decided to go with a wind turbine built in the USA
by Missouri Wind And Solar.Notice the MW logo on the tail fin.
100% Manufactured in Seymour Missouri,The Show Me State!
OUR MISSOURI WIND TURBINES ARE TUFF ENOUGH FOR SUZLON,HOW ABOUT YOU?
We do not mark items as gifts or under report values for customs. For International buyers it is strongly recommended to check your own countries tax practices as we do not pay your taxes,duty or customs fees.
We do not over charge for shipping it is simply what the shipping calculator comes up with. Customs fees or taxes are not included in shipping,it is your responsibilty to pay them.
Questions and answers about this item
No questions or answers have been posted about this item.
(estimated and based on max bid)To be provided at checkout
Your max bid:
Your max bid:
By clicking Confirm bid, you commit to buy this item from the seller if you are the winning bidder.
By clicking Confirm bid, you are committing to buy this item from the seller if you are the winning bidder and have read and agree to the Global Shipping Program terms and conditions - opens in a new window or tab. Import charges previously quoted are subject to change if you increase you maximum bid amount.