Using this system,you...
The passive keyless entry system is a new electrical product for vehicles. It is safer and more convenient for users
than the traditional RKE system. It uses RFID technology,providing the highest security available.
Superior PKE solution from TI.
Three slim LF antennas and 3D coil offers High sensitivity and accuracy in identifiaction.
Nullifies Frequency Jamming Devices.
Mutual authentication technology and hoping code.
Low Power Consumption.
Automatic Door Locking(Arming).
Automatic Door Unlocking(Disarming).
Unclosed Door Warning.
Remote Door Locking/Unlocking.
Automatic Window Closing(Optional).
Remote Start (Optional,need Button Start system).
Passive Door locking
By simply walking over 2.5 or 3 meters away from your car, doors will lock automatically and ARM security system.Unlock Doors Automatically
As you approach your vehicle and arrive in range of 1.5 to 2 meters, the system will identify the driver who has a valid access key and unlock the doors immediately.
The PKE system still includes an immbolizer function. Once users enter the vehicle and attempt to start the engine,the vehicle will verify the driver's access key, if a valid access key is identified, the LED will turn off allowing the driver to start the vehicle. If not, the horn and lights will sound and flash an alarm,and the vehicle engine can not be started.
Unclosed Door Alarm
If driver leaves the vehicle without closing a door or doors, the system will remind you with a separate open door alarm when the key leaves the contact range.
Lock after first Braking
Doors of the vehicle will lock automaticlly when the driver step the brake at the first time after the key been turned to ACC or ON.
Automatic Power Saving
if the driver leaves the vehicle alone over 36 hours, the system will enter POWER SAVING mode to avoid exhausting the power of the car battery.
How to use?
The installation please ref to manual, but we suggest you take your car to install the PKE by a skilled machinist.
Part 2: Button Start KG02
What is one-key start and its function?
As we all know, when we want to start a car, we need to use a car key. But when you lose your key, you can not drive your car any more. Therefore, we invent this product to make people's life more convenient.
Button Start / Keyless Go System
Button Start / Keyless GO System is a new electrical appliance designed for vehicle
aftermaket . With this system,driver can start/stop the vehicle engine without turning key.
Specification & features
1. Low consumption standby currency: 0.6mA@12V
2. Large range of working voltage: 9.0V?24.0V
3. Working temperature: -40°C~85°C
4. 4 channel currency drive (40A): ACC, IG1, IG2, and START.(Not Relay: ACC,IG1,IG2and Start are all controlled by IC,this can avoid power failure in driving.)
5. Adopts original imported ignition IC instead of a relay which may cause touching point burnt or broken off when shaken.
6. Built-in double-button switch
7. High-temperature protection, high-voltage/short circuit protection
8. Power-off memory function supported to make sure the safety of driving
9. We use MCU imported from Microchip Company in USA for a stable capability and functioning
10.Disarmed by the driver`s remote controller.
How to use?
1. Power connected: if you just want to listen to music, just press the blue POWER BUTTON one time and ACC will be on. When you press it once more, it will power off.
2. Engine start: Keep pressing the brake, and press POWER BUTTON lightly and your engine will retrofire automatically.
How can I do if it can not be ignited due to low temperature in winter or low battery?
You can keep pressing the brake and POWER BUTTON at the same time until car is started.
3. Flameout: When engine is working, press the brake and then press POWER BUTTON for 0.5 Seconds and your engine will stop working automatically.
Disarm / Arm: when the driver unlock the vehice by his(her) remote controller,the system disarm automatically,and 30 seconds later, if ACC or ON is not on, the system will enter arm state automatically.
ACC: in disarming state, push the button once.
ON: in disarming state, push the button twice.
Start: in disarming state, pushing the button 3 seconds, or stepping the brake and push the button once.
When the voltage of the vehicle battery is not sufficient or in winter, maybe you need longer time to start the vehicle, pushing the button for a serveral seconds can extend the time of ignition.
Stop: step on the brake and pushing the button 0.5 seconds.
1. Q: What kind of cars can The item be applied to?
A: The item is universal, can use in all kinds of Private Car, Minibus, Truck etc.
2. Q: How can I remove directional lock when I install the push start system?
A: This a common question from customers. You have to end the key in the slot and this is the precondition to install the push start system.
3. Q: Can it be installed in a car with chip?
A: Regarding to the car with engine chip, you need to remove the chip in the key handle and stick it near to ignition switch in order to react to the engine.
4. Q: Do I need to open an additional hole for the push button?
A: It is not necessary. We use covered button in order to keep your car in original, you just need to stick it to cover on the start switch.
5. Q: will it be difficult to install the system?
A: it is easy to install, you just need to connect all the cables correctly according to the install instruction. Generally, we recommend it be installed by a professional mechanic.