Details about 1997-2004 LS1-LS6-Vortec 4.8-5.3-6.0 V8 fuel injection wiring harness/pcm kit1997-2004 LS1-LS6-Vortec 4.8-5.3-6.0 V8 fuel injection wiring harness/pcm kit See original listing
May 14, 2012 18:00:00 PDT
[ 2 bids ]
Midwest City, Oklahoma, United States
Remanufactured: A properly rebuilt automotive part. The item has been completely disassembled, cleaned, and examined ... Read moreabout the condition
You are bidding on a harness custom built to put a 1997-2004 Camaro/Firebird LS1-Corvette LS1/LS6 or1999-2006 Vortec 4.8-5.3 or 6.0L in an older non computer vehicle, with a Turbo 350/400, 200R/700R, 4L60E or Manual Transmission. If you are looking to put a 21st century power plant in your older classic, this is the ticket.
This harness retains all the functions as a stock harness allowing to run only the front O2 sensors (left and right) which is required. All other non emission functions will be programmed out of the PCM, IF you are legally allowed to run a non-emission LS1-Vortec V8.The VSS is also required.
The connectors from the pcm to the centerline of the engine is 50 inches, you must measure carefully to allow for proper installation. I can modify the harness to up to 65" maximum, and I will need to know where you plan to mount the computer (pcm).
All factory standard connectors for the GEN III is provided:
BE AWARE OF OTHERS SELLERS ONLY SELLING "PARTIAL" HARNESSES! - No DLC, Fuel Pump Relay, Fan Relays, Transmission controls etc., and hit you with hidden charges! Always ask the "other" guys, what the TOTAL cost will be!
* If you do not have the coil pack harness, I can build these into the harness for a neater appearance.
Other items that are available, at no additional costs!
Items available for a fee:
Cruise Control Option: This includes the connector for the electronic cruise module, associated wiring and pig tail wires for the brake switch for the automatic transmission or the brake switch and clutch switch for the manual transmission. The switches and associated brackets are not included and must be purchased independently. COST: $25.00
DBW Connections: $100.00
NOTE: Support for the DBW (Drive By Wire) is available BUT you must have the correct throttle body, TAC module AND pedal for the model year engine. This is an extra cost option to supply ONLY the connections to the DBW devices.
(1) Differences between the fuel injector connectors: the Bosch style is on the left, the Vortec Gen III 4.8, 5.3 and 6.0L connectors on the right side (see picture). (2) The differences between the MAF sensors are in next picture: 3 pin MAF and the 5 pin (right side) that uses the integrated IAT sensor. (3 & 4) Differences for the coil connectors ( LS1 style on the left, Vortec/LS2 coil)
1 2 3 4
I will also need to know the style of O2 sensor connector you are using (see picture below). If you don't have your O2 sensors, the flat plug design connectors will be incorporated in your harness unless otherwise specified. NOTE: This is the O2 sensor side. 1 year Warranty is provided for covering repairs due to workmanship only. Does not cover wrong application, misuse, abuse or alterations, wrong installation practices, wiring installed by purchaser to complete installation or lack of knowledge on the part of the purchaser/installer.
I will also need to know the style of O2 sensor connector you are using (see picture below). If you don't have your O2 sensors, the flat plug design connectors will be incorporated in your harness unless otherwise specified. NOTE: This is the O2 sensor side.
1 year Warranty is provided for covering repairs due to workmanship only. Does not cover wrong application, misuse, abuse or alterations, wrong installation practices, wiring installed by purchaser to complete installation or lack of knowledge on the part of the purchaser/installer.All connections are crimped and soldered to insure a positive long lasting termination.
Also included is the pcm (service number 12200411) with the programming for a STOCK 1997-2003 LS1, LS6, 1999-2003 Vortec 4.8, 5.3, 6.0L engine, with all the unnecessary codes deleted. No custom programming!
NOTICE NOTICE NOTICE
Later year engines from 2004 through 2006, use a different pcm with different calibration formats and must be purchased separately to match engine year. These can be purchased through me, but there is limited availability, please contact me first before purchase.
NOTICE! I will need to know the following information, without it I cannot properly program the pcm to run efficiently.
Please, If you are paying via Paypal, included this information on payment.
MY PCM's are NOT locked, so you can do your own programming if desired in the future!
Installation instructions on CD is included, over 70 pages of basic installation and troubleshooting information!
I prefer payment through Paypal but will accept alternative payment methods, email me for instructions. USPS Large Flat Rate Priority Shipping w/ins. will be $22.00 in the 50 United States of America, Puerto Rico. Due to problems with international shipping, this item will not be shipped outside the U.S.A., Canada.
Payment is due within 3 days of auction end.