Operation instruction for LED watch

Views 7 Likes
Like if this guide is helpful

Operation instruction for Touch screen LED watch

  • 1. Press your finger to the screen and the time is displayed.
  • 2. Press left part screen again and wait a few seconds, the current hourly setting will blink and then press the screen to change the number and press it for a few seconds to confirm. After setting the correct hour, you will be allowed to change the minute settings as well.
  • 3. Following, press screen for a few seconds again and you can also set Year and Date orderly.


Operation instruction for Mirror Face LED Watch








 

  • It has A,B,C and D four buttons.A and B are the waking up buttons. C is the selecting button and D is setting button.
  • press D in 2 seconds to adjust the time, date, year(2000-2050)
  • 12 hex or 24 hex(time period) and then press C button to select and finally confirmed by D button.
 

Operation instruction for LAVA LED Watch

Power

Insert one CR2032 battery to power the device.
Change the batteries when the luminosity is too weak.
 

Reading Time,Date,Seconds

(1)Press the button A once
The upper two characters display from 0 to 23 hours
The lower two characters display from 1 to 59 minutes
(2)Press the button A twice
The upper two characters display from 1 to 12 months
The lower two characters display from 1 to 31 days
(3)Press the button A three times
The lower two haracters display the seconds
 

Setting Hour,Minute,Month,Day,Year,12Hr/24Hr Mode

Push the button A to display Time,then push the button B to enter set mode (hours are flashing).
Press button A to set the hours.Push the button B to confirm the hour and to change to the
minutes (flashing).
Press button A to set the minutes.Push the button B to confirm the minutes and to change to the
month (flashing).
Press button A to set the month.Push the button B to confirm the month and to change to the days
(flashing).
Press button A to set the days.Push the button B to confirm the days and to change to the year
(flashing).
Press button A to set the year.Push the button B to confirm the year and to change to the
12Hr/24Hr Mode (flashing).
Press button A to set the 12Hr/24Hr Mode (flashing).Push the button B to confirm the 12Hr/24Hr
Mode.















 

Battery advice

Replacement of batter/batteries(we recommend by the specialized trade)
Please replace the batteries as follows:
Remove the screws on the back of the watch case and/or open the watch case. If necessary lift the metal clip that fixes the batteries at end which a thin pointed tweezers or screwdriver and remove it.Replace the batteries considering the polarity.Close the watch case and if necessary tighten the screws.

 

Operation instruction for Matrix LED Watch

Button A (the top right one)=Set      Button B(the bottom right one) =Mode
Top Right Sub-dial=Hour / Month / Day
Bottom Sub-dial =Minute / Date / Level of Brightness
On/ Off LED-Press A for 3 seconds to turn on or turn off LED
Press A 1 time to read Time.
Press A 2 times to read Date.
Press A 3 times to read Day.
1.Set Time
Press A to turn on LED. At TIME mode, press B the Light (Hour) will flash and then press A to increase the number. After setting Hour, press B to set minute (light will flash) as well.
2.Set Date & Day
After setting TIME, press B again to set Month / Date / Day orderly.
3.Set Brightness
After setting DAY and press B again, the blue light of the button digit 1,2,3,4 will flash and you can press A to set the level of brightness.
4.Set Automatic Display
After setting brightness and press B, it will enter into the back light setting mode. Press A to select 05/ 10 / 15 / 20 / 30 so the watch will automatically display the time per 5 / 10 / 15 / 20 / 30 minutes. Or you can close the function while the light (ON/OFF) is flashing and then press B.
 
If you have any question or need more detail, please feel free to contact us via eBay message, we will do the best to resolve any problem for you, thank you!


 
Have something to share, create your own guide... Write a guide
Explore more guides